ASTM F2030-21 PDF

Full title and description

Standard Specification for Paintball Cylinder Burst Disk Assemblies — Specification F2030-21 defines the physical, material, marking, performance and installation requirements for burst (rupture) disk assemblies used as overpressure protection on paintball marker propellant cylinders.

Abstract

This specification covers burst disk (rupture disk) assemblies intended for paintball marker propellant sources. It defines materials and manufacturing requirements (corrosion resistance, chemical compatibility), required mechanical performance and burst/rupture pressure tolerances, minimum venting/relief-hole features, inspection and marking requirements, and installation/fit criteria. The document references applicable venting/flow criteria and transport/manufacture requirements and is intended to ensure that burst disk assemblies reliably vent cylinders at their designed rupture conditions and are safe and traceable in service.

General information

• Status: Published (original edition approved June 1, 2021). Users should verify current status with ASTM International (some third‑party listings may indicate revision or withdrawal; confirm before relying on the standard for certification or procurement).
• Publication date: June 1, 2021 (designation F2030-21).
• Publisher: ASTM International (Committee F08 on Sports Equipment, Subcommittee F08.24 on Paintball and Equipment).
• ICS / categories: 97.220.40 (Outdoor and water sports equipment) — sports equipment / paintball safety devices.
• Edition / version: F2030-21 (2021 edition).
• Number of pages: 3 (concise specification).

Scope

F2030-21 applies to burst disk assemblies designed for use with paintball marker propellant cylinders and specifies requirements for their design, materials, manufacture, performance (rupture/burst behavior and venting), marking and installation/inspection. Units and values in the standard are expressed in inch–pound units. The standard is limited to the burst disk assembly and its mating port features and does not claim to address every safety concern associated with cylinder systems; users remain responsible for applying appropriate safety and regulatory practices.

Key topics and requirements

• Materials and manufacture: corrosion‑resistant materials, chemical compatibility with the propellant, avoidance of galvanic action, and burr‑free port/assembly features.
• Burst/rupture performance: prescribed rupture pressure tolerances and test-pressure basis (rupture behavior required to occur within specified percentage of test pressure as defined in the standard).
• Relief/venting design: minimum number and placement of relief holes (example: at least two holes, 180° apart) and orientation to reduce thrust and cylinder spin; relief flow sufficient to vent the cylinder per referenced flow criteria.
• Single‑use design: assemblies are non‑resettable and require replacement after activation.
• Marking and traceability: burst disk assemblies must be marked with manufacturer code and rated burst pressure (and other identification as required by the specification).
• Inspection and installation: requirements for visual inspection of relief holes, verification of physical envelope/fit, cleanliness and suitability of mating port prior to installation.
• Referenced regulatory/testing criteria: alignment with applicable DOT/transport regulations and CGA venting/test guidance for compressed gas devices (as cited in the standard).

Typical use and users

Primary users include paintball cylinder and marker manufacturers, burst/rupture disk component manufacturers, quality and safety engineers, testing and certification laboratories, equipment rental operators and distributors, and procurement/specification authors in the paintball and compressed‑gas sporting goods sector. The standard is used to specify and verify overpressure protection components supplied with or fitted to paintball propellant cylinders.

Related standards

Commonly referenced documents and regulatory guidance associated with F2030-21 include DOT hazardous-materials/transport regulations (49 CFR) and Compressed Gas Association (CGA) guidance on rupture/venting performance (for example CGA S‑1.1 referenced for venting/test criteria). F2030 is maintained under ASTM Committee F08 (Sports Equipment); users should consult ASTM listings for related F08 paintball equipment standards and any later revisions or companion standards.

Keywords

burst disk; rupture disk; burst disk assembly; paintball cylinder; paintball marker; propellant cylinder; overpressure protection; relief hole; burst pressure; CGA S-1.1; DOT 49 CFR; ASTM F2030

FAQ

Q: What is this standard?

A: ASTM F2030-21 is the Standard Specification for Paintball Cylinder Burst Disk Assemblies; it sets requirements for the materials, design, performance, marking and installation of burst (rupture) disk assemblies used on paintball propellant cylinders.

Q: What does it cover?

A: It covers physical and material requirements, burst/rupture performance and tolerances, relief/venting hole design and orientation, single‑use requirements, marking/traceability and inspection/installation checks for burst disk assemblies intended for paintball marker propellant sources.

Q: Who typically uses it?

A: Manufacturers of paintball cylinders and burst disk assemblies, safety and quality engineers, test labs, equipment vendors, rental operators and procurement/specification professionals in the paintball and compressed‑gas sporting goods sectors.

Q: Is it current or superseded?

A: The original F2030-21 edition was approved and published June 1, 2021. Users should verify the standard’s current status (active, revised, reapproved or withdrawn) with ASTM International or an official standards catalog before relying on it for compliance or procurement, since third‑party listings can differ and revisions may be issued after the 2021 edition.

Q: Is it part of a series?

A: F2030 sits under ASTM Committee F08 (Sports Equipment) and Subcommittee F08.24 (Paintball and Equipment). There are related historical and companion F2030 editions and other ASTM F08 paintball equipment standards; consult ASTM for the complete suite of related standards and any linked documents.

Q: What are the key keywords?

A: Burst disk, rupture disk, burst disk assembly, paintball cylinder, propellant, burst pressure, relief hole, overpressure protection, CGA S-1.1, DOT 49 CFR, ASTM F2030.