DIN EN ISO 13297 E 2014-06 PDF

Full title and description

STB DIN EN ISO 13297 E 2014-06 — Small craft - Electrical systems - Alternating current installations. German version (FprEN / draft) corresponding to ISO/FDIS 13297:2014; specifies requirements for low-voltage single-phase alternating-current installations on small craft.

Abstract

This document establishes requirements for the design, construction and installation of low-voltage alternating-current electrical systems installed on small craft (single-phase AC systems with nominal voltages up to 250 V). It addresses cabling, protection (overcurrent and residual-current protection), earthing, installation methods, marking and safety measures specific to small craft electrical installations; it excludes higher-voltage electric propulsion systems covered by other standards.

General information

• Status: Withdrawn / draft German FprEN edition (was issued as a draft national version and subsequently superseded by later editions).
• Publication date: 2014-06-01 (June 1, 2014).
• Publisher: Deutsches Institut für Normung (DIN) — German national version of an ISO/CEN work item.
• ICS / categories: 47.080 (Small craft); 47.020.60 (Electrical equipment of ships and marine structures).
• Edition / version: E DIN EN ISO 13297 E (FprEN / draft national edition, 2014-06).
• Number of pages: Approx. 34–35 pages (published draft edition commonly listed as 35 pages).

Scope

The standard covers requirements for single-phase alternating-current electrical systems installed on small craft (normally craft with hull length up to about 24 m), operating at nominal voltages not exceeding 250 V AC single-phase. It is intended to ensure personnel protection, electrical system safety and fire protection for the craft electrical installation; it does not cover high-voltage or three-phase propulsion systems addressed by separate standards.

Key topics and requirements

• System design principles for low-voltage single-phase AC installations on small craft.
• Cabling selection, routing and mechanical protection appropriate for marine environments.
• Overcurrent protection and coordination (fuses, circuit-breakers) for AC circuits.
• Residual current devices and requirements for earth-leakage protection.
• Protective earthing, bonding and equipotential measures specific to small craft.
• Installation practices: mounting, enclosure IP ratings, ventilation and separation from ignition sources.
• Marking, identification of conductors and terminals, and documentation requirements for safe operation and maintenance.
• Limitations and exclusions (for example, electric propulsion systems are covered by ISO 16315).

Typical use and users

Engineers and designers of small craft electrical systems, boatbuilders, marine electricians and installers, surveyors and classification society assessors, certification bodies and regulators applying recreational craft or marine safety requirements. The standard is used as a technical reference for safe installation and for demonstrating compliance with applicable marine directives and national regulations.

Related standards

Commonly referenced companion standards include ISO 10133 (extra‑low‑voltage DC installations on small craft), ISO 16315 (electric propulsion systems), ISO 9094 (fire protection on small craft), ISO 10088 (permanently installed fuel systems) and relevant IEC standards such as IEC/EN 60529 (IP code) and IEC 61009/61009-1 for residual-current devices and RCBOs. These documents are typically cross-referenced for complete electrical and safety requirements.

Keywords

Small craft, electrical systems, alternating current, AC installations, low-voltage, earthing, residual current device (RCD), overcurrent protection, cabling, marine installations, boat electrical safety.

FAQ

Q: What is this standard?

A: DIN EN ISO 13297 (2014-06 draft edition) is a German national publication of the ISO work item titled "Small craft — Electrical systems — Alternating current installations", providing requirements and guidance for single‑phase AC electrical installations on small craft.

Q: What does it cover?

A: It covers design, construction and installation requirements for low‑voltage single‑phase AC systems on small craft (nominal AC voltage up to 250 V), including cabling, protection devices, earthing/bonding, marking and installation practices; it excludes higher‑voltage propulsion systems.

Q: Who typically uses it?

A: Boat designers, marine electricians, shipyards, surveyors, classification societies and certification bodies use the standard when specifying, installing, inspecting or certifying AC electrical systems on small craft.

Q: Is it current or superseded?

A: The 2014 draft/national edition has been superseded by later consolidated editions of ISO 13297 and corresponding EN/DIN publications (notably ISO 13297:2020 and subsequent EN/DIN translations and amendments). Users should refer to the latest published edition and any amendments for current requirements.

Q: Is it part of a series?

A: Yes — ISO 13297 is part of the small craft electrical systems family of standards; it complements ISO 10133 (DC installations) and is intended to be used alongside related small craft standards covering fuel systems, fire protection and propulsion as appropriate.

Q: What are the key keywords?

A: Small craft, AC installations, alternating current, low-voltage, earthing, RCD, overcurrent protection, cabling, marine electrical safety.