GOST 22233-2001 PDF

Full title and description

GOST 22233-2001 — "Профили прессованные из алюминиевых сплавов для светопрозрачных ограждающих конструкций. Технические условия" (Aluminium alloy extruded sections for translucent envelopes — General specifications). The standard specifies technical requirements for hot-extruded aluminium‑magnesium‑silicon system profiles intended for use in glazed and translucent building envelope systems, including semifinished and finished profiles up to a circumscribed circle diameter of 300 mm.

Abstract

This interstate (GOST) standard sets classification, dimensional and tolerance requirements, chemical composition and mechanical properties, surface‑treatment and corrosion requirements, sampling and acceptance rules, and test methods for extruded aluminium profiles used in translucent enclosing (glazed or curtain‑wall) constructions of buildings. It includes normative references to related ISO/EN and national standards and was published with at least one formal amendment.

General information

• Status: Withdrawn / superseded (replaced by a later edition; original GOST 22233-2001 ceased to be in force as of its stated end-of-validity date).
• Publication date: Adopted 30 May 2001; Date of introduction (effective date) 1 July 2002; (document editions/prints show publication activity through 2004).
• Publisher: Issued as an interstate standard under the authority of the Russian/MNTKS construction standards bodies and published as a GOST technical specification (Gosstandart/Gosstroy channels).
• ICS / categories: 77.150.10 (Aluminium and aluminium alloys; products and semi‑finished articles).
• Edition / version: GOST 22233-2001, with Amendment No.1 adopted 14 May 2003 (change entered 01 October 2003).
• Number of pages: Approximately 49 pages (typical published PDF/print editions).

Scope

The standard applies to hot‑extruded aluminium profiles of the Al‑Mg‑Si system intended for use in translucent (glazed) enclosing building structures and curtain‑wall systems. It covers profiles and semifinished sections with a circumscribed circle diameter up to 300 mm, and includes requirements for materials, dimensions and tolerances, mechanical properties, surface finishes (including anodizing and organic coatings), corrosion resistance, marking, packing, and conformity assessment. Use for non‑translucent constructions is allowed only with appropriate technical and economic justification.

Key topics and requirements

• Classification and designation of extruded aluminium profiles for translucent envelopes.
• Permitted alloys and chemical composition limits (Al‑Mg‑Si system, commonly including grades equivalent to 6060/6063 and regional alloys such as AD31, with specified compositional ranges).
• Mechanical property requirements and condition states (tolerances for tensile strength, yield, elongation as applicable to profile use in building envelopes).
• Dimensional tolerances, section geometry limits, and maximum circumscribed diameter (≤ 300 mm for individual aluminium elements).
• Surface‑treatment requirements (anodizing and organic coatings), including acceptance criteria for coating quality and corrosion resistance tests (normative test methods referenced).
• Rules for sampling, inspection, and acceptance testing (including visual, dimensional, mechanical and corrosion tests); required documentation and marking.
• Normative references to relevant ISO and EN documents (for example ISO/EN standards on extrusion tolerances, corrosion testing, and alloy designation) and to national GOST norms governing related tests and materials.

Typical use and users

Primary users are aluminium extruders, façade system manufacturers, curtain‑wall fabricators, architects and structural engineers specifying glazed façades, quality and testing laboratories, and procurement/certification bodies. The standard is used to ensure consistent material, dimensional and performance characteristics for profiles applied in curtain walls, storefronts, skylights and other translucent building enclosures.

Related standards

The standard references and aligns with various ISO and EN standards (examples noted in the amendment include ISO 1519, ISO 2813, ISO 2815, EN 515, EN 573-3, EN 755 series, ISO 9227, prEN 14024) as well as numerous national GOST test and materials standards for corrosion, coating, mechanical testing and alloy composition. It replaced the earlier GOST 22233-93 and was later replaced by a newer edition (GOST 22233-2018).

Keywords

GOST 22233-2001; aluminium profiles; extruded sections; Al‑Mg‑Si alloys; curtain wall; translucent envelopes; façade profiles; dimensional tolerances; surface treatment; anodizing; corrosion resistance; acceptance tests.

FAQ

Q: What is this standard?

A: GOST 22233-2001 is an interstate (GOST) technical standard that specifies technical conditions for hot‑extruded aluminium profiles intended for use in translucent building envelope and façade systems.

Q: What does it cover?

A: It covers classification, chemical composition and alloy grades (Al‑Mg‑Si system), mechanical properties, dimensional tolerances, surface treatment and corrosion requirements, sampling and acceptance rules, test methods and normative references for profiles up to a circumscribed diameter of 300 mm used in glazed or translucent enclosures.

Q: Who typically uses it?

A: Aluminium extruders, façade and curtain‑wall fabricators, façade designers and engineers, testing laboratories, and compliance/certification authorities involved in building envelope products and systems.

Q: Is it current or superseded?

A: GOST 22233-2001 has been superseded by a later edition (noted in national databases as replaced by GOST 22233-2018) and the 2001 edition was recorded with an end‑of‑validity date in national registries (the 2001 text shows revision history and an amendment). Users should reference the currently valid edition for procurement and compliance.

Q: Is it part of a series?

A: It continues and replaces earlier national documents on extruded aluminium profiles for building constructions (it replaced GOST 22233-93) and is interlinked with other GOST/ISO/EN standards covering aluminium alloys, testing, and surface treatments.

Q: What are the key keywords?

A: Aluminium extruded profiles; Al‑Mg‑Si alloys; curtain wall; façade profiles; anodizing; corrosion testing; dimensional tolerances; GOST 22233.