ISO 6282-2018 PDF
Name in English:
St ISO 6282-2018
Name in Russian:
Ст ISO 6282-2018
Original standard ISO 6282-2018 in PDF full version. Additional info + preview on request
Full title and description
Plain bearings — Metallic thin-walled half bearings — Determination of the σ0,01*‑limit (ISO 6282:2018). This International Standard specifies a laboratory method for determining the σ0,01*‑limit of the steel backing used in thin‑walled multilayer half plain bearings, primarily for bearing diameters up to 80 mm (and applicable up to 160 mm in certain cases).
Abstract
ISO 6282:2018 defines the test apparatus, preparation of specimens, test procedure, calculation and expression of results needed to determine the σ0,01*‑limit of the steel backing in metallic thin‑walled multilayer half bearings. The method supports consistent evaluation of backing material performance for design, quality control and conformity assessment.
General information
- Status: Published (International Standard).
- Publication date: June 2018 (Edition 2, 2018-06).
- Publisher: International Organization for Standardization (ISO).
- ICS / categories: 21.100.10 — Plain bearings.
- Edition / version: Edition 2 (2018).
- Number of pages: 5 (ISO published PDF).
Scope
Specifies a method for determining the σ0,01*‑limit for the steel backing of thin‑walled multilayer half plain bearings for bearing diameters up to 80 mm; the method can also be used for diameters up to 160 mm. The standard provides definitions, required apparatus, specimen preparation, test procedure, expression of results and an informative annex as needed for reproducible measurement.
Key topics and requirements
- Definition and significance of the σ0,01*‑limit for steel backing in thin‑walled multilayer half bearings.
- Required test apparatus and calibration requirements for reproducible measurement.
- Specimen preparation and handling to ensure representative results.
- Step‑by‑step test procedure, data recording and calculation method for reporting the σ0,01*‑limit.
- Expression and reporting of results to support material acceptance and quality control decisions.
Typical use and users
Used by bearing designers, materials engineers, quality laboratories, OEMs and suppliers of metallic multilayer plain bearings to verify backing steel properties, support material selection, perform acceptance testing and investigate failures. Test houses and national standards bodies implementing or adopting ISO technical content will also reference this document.
Related standards
ISO 6282:2018 is part of the plain‑bearings family of standards and is related to other ISO documents covering metallic multilayer plain bearings, wrapped bushes and nondestructive bond testing (examples of related or neighboring standards include ISO 4386 series and ISO 3547 series as adopted/linked by national bodies). National/adopted versions (DIN, BS, etc.) exist for a few markets.
Keywords
plain bearings, thin‑walled half bearings, metallic multilayer bearings, σ0,01*‑limit, steel backing, bearing test method, bearing quality control, ISO 6282:2018.
FAQ
Q: What is this standard?
A: ISO 6282:2018 is an International Standard that specifies a laboratory method for determining the σ0,01*‑limit of the steel backing used in metallic thin‑walled multilayer half plain bearings.
Q: What does it cover?
A: It covers definitions, test apparatus, specimen preparation, the test procedure, calculation and expression of the σ0,01*‑limit and an annex with supplementary information for bearings up to 80 mm diameter (and applicable up to 160 mm where noted).
Q: Who typically uses it?
A: Bearing manufacturers and suppliers, materials and mechanical engineers, independent test laboratories, OEMs specifying bearing performance and national standards adoption bodies.
Q: Is it current or superseded?
A: ISO 6282:2018 (Edition 2) is the current published version that superseded ISO 6282:1983. Users should check national adoption status for any later revisions or confirmations by their national standards body.
Q: Is it part of a series?
A: It sits within the broader set of plain‑bearings standards (ISO plain bearings series) and is related to other documents that address multilayer bearing testing, wrapped bushes and nondestructive bond testing (for example ISO 4386 and ISO 3547 series as complementary standards).
Q: What are the key keywords?
A: plain bearings; thin‑walled half bearings; metallic multilayer; σ0,01*‑limit; steel backing; test method; bearing quality control; ISO 6282.