PD IEC TR 63036-2016 PDF

Full title and description

IEC TR 63036:2016 — Electrical interface specification for phase-cut dimmer in phase-cut dimmed lighting systems. This technical report specifies electrical interface parameters and test procedures for controlling mains-operated electronic lighting equipment by mains-voltage phase-cut dimming (including LED integrated lamps and light sources with external control gear). Safety requirements are excluded and remain the responsibility of applicable product standards.

Abstract

IEC TR 63036:2016 defines the electrical interface characteristics, expected behaviour and test methods for phase-cut dimmers and for luminaires or lamps intended to be controlled by such dimmers. It addresses compatibility and performance aspects (waveform characteristics, control range, flicker/instability conditions and test procedures) for mains-voltage phase-cut dimming of electronic lighting equipment, and identifies which types of devices should meet the interface requirements. Safety provisions are explicitly out of scope.

General information

• Status: Published — Technical Report (TR), active / valid.
• Publication date: 16 August 2016.
• Publisher: International Electrotechnical Commission (IEC).
• ICS / categories: 29.020 (Electrical engineering in general).
• Edition / version: Edition 1.0 (2016).
• Number of pages: 33 pages.

Key bibliographic and status data as published by the IEC webstore and national adopters.

Scope

Specifies electrical interface requirements and test procedures for control by mains-voltage phase-cut dimming of the brightness of mains-operated electronic lighting equipment intended to be controlled by phase-cut dimmers. The document applies to LED integrated lamps and light sources with external control gear, and indicates that electronic switches with comparable circuitry (but without adjustable phase-cut angle) should meet the same interface requirements. The report excludes product safety requirements, which are covered by the respective product standards.

Key topics and requirements

• Electrical interface definitions for phase-cut dimmers (leading-edge and trailing-edge characteristics).
• Test procedures to assess dimming compatibility of mains-operated electronic lighting equipment (including waveform measurement and behaviour under specified loading conditions).
• Performance characteristics to be measured (control range, minimum dimming level, stability, flicker/instability conditions and recovery behaviour).
• Application to LED integrated lamps and control-gear based light sources; implications for product design and dimmer-lamp interoperability.
• Clarification that safety requirements are out of scope and must be met via the applicable product safety standards.

These topics are summarized from the technical report and related national/adoption records.

Typical use and users

Used by lighting product designers and manufacturers (LED lamps, drivers and luminaires), lighting system integrators, test laboratories performing compatibility and dimming performance tests, certification bodies, and standards committees developing related product and instal‑lation standards. The TR is commonly consulted when designing or validating products expected to be compatible with mains phase-cut dimmers.

Related standards

Cross-references and related documents commonly cited with IEC TR 63036 include product and performance standards for lamps, controlgear and installations such as IEC 62504 (LED product considerations), various IEC product standards covering safety and performance, and companion TRs in the 630xx series. National adopters/implementers may list specific cross-references used in test regimes.

Keywords

phase-cut dimmer, phase-cut dimming, mains dimming, LED integrated lamp, electronic lighting equipment, electrical interface, dimmer-lamp compatibility, dimming test procedures, flicker, control gear.

FAQ

Q: What is this standard?

A: IEC TR 63036:2016 is a technical report that specifies the electrical interface and test procedures for mains-voltage phase-cut dimming of electronic lighting equipment (e.g., LED integrated lamps and light sources with external control gear).

Q: What does it cover?

A: It covers interface definitions, expected behaviour and test methods for phase-cut dimming compatibility and performance (control range, minimum level, stability and related measurements). It does not cover product safety requirements.

Q: Who typically uses it?

A: Lighting manufacturers (lamps, drivers, luminaires), test laboratories, certification bodies, system integrators and standards developers use this TR when assessing or specifying dimmer–lamp interoperability.

Q: Is it current or superseded?

A: Published 16 August 2016 (Edition 1.0). The IEC record shows the TR with a stability indication through 2028; users should check national adoption records or the IEC webstore for any corrigenda or newer documents before relying on the text for regulatory or compliance decisions.

Q: Is it part of a series?

A: Yes—IEC TR 63036 is part of the wider 63000-series work items addressing lighting and related topics; there are companion TRs and technical specifications within the 630xx range that address other aspects of LED lighting, measurement and performance.

Q: What are the key keywords?

A: phase-cut dimmer; phase-cut dimming; mains-voltage dimming; LED integrated lamp; electronic control gear; dimmer-lamp compatibility; dimming test procedures; flicker; electrical interface.